Greenflag Karting Forum Board

Number of entries: 50 Number of pages: 5
1 2 3 4 5 | Next > | Last >>

Submitted by

Comments:

Name: emraan
E-mail: Contact

Private post. Click to view.

Added: August 30, 2010

Submitted by

Comments:

Name: Tom Barth
E-mail: Contact

Congrats to Aaron and Bob also.

I am happy that TM is a great powerplant for short track AND long track.

I didn't know Bob was back in town or is he still in FL?

I will be updating web site soon with new low cost upgrades for the TM ICC.

Dan and I are finding out that there is much to be gained 'below' the cylinder base gasket! I'll keep you posted

Added: August 25, 2010

Submitted by

Comments:

Name: John Pickens
E-mail: Contact

I almost forgot to thank my other sponsors.
MG Tires , Amsoil, Go Pro helmet Cams, Juniors Wood Fired BBQ, and Life Thread

Added: August 25, 2010

Submitted by

Comments:

Name: John Pickens
E-mail: Contact

Thanks Tom. TM K9's had and excellent weekend at Putnam with Aaron Jones winning Saturday's WKA 125 Shifter 1 and me winning Sunday. Bob Anderson nabbed 2nd place both days in his TM Moto. TM's rock. I think I would havd given Aaron a good run on Saturday. I was leading when my clutch went. My fault. I had the clutch cable too tight but I learned some things form that and will move on to New Jersey Motorsports Park and a shot at the tiyle next month. Mad Money Racing (me and Bob) want to thank you for your support and advice Tom. You've kept us on track and fast.

Added: August 25, 2010

Submitted by

Comments:

Name: Tom Barth
E-mail: Contact

Congrats to John Pickens for his TM ICC win at Putnam Park last weekend.

Added: August 25, 2010

Submitted by

Comments:

Name: joe
E-mail: Contact

hi tom,u said look @ piston top,but is there a number stamped somewhere so i can know the size,i need to order a new top end from u asap,thanx again

Admin reply: Joe,

There should be a size number on top of piston. It usually is 53.93 which indicates that the piston is 53.93mm in diameter. See if you can find it.

Added: August 23, 2010

Submitted by

Comments:

Name: Raphael
E-mail: Contact

Hi Tom, today i write you to know the ignition time advance in mm from TDC for my Tm K9 LT with 4000 wind stator by Pvl.

In the second time, i would to know where i can buy the 11cc combustion chamber insert.

Thank you for all.
My best Regards.
Raphael

Admin reply: Hi Raphael,

Set ignition timing for 4000 wind stator at .063" or about standard.

I am sorry I missed your request. I will send you invoice for HC insert.

Added: August 20, 2010

Submitted by

Comments:

Name: joe
E-mail: Contact

Hi tom,im buying n icc k9b,but the previous owner dont have a clue of the size of the piston currently in the motor,how do i know what size to buy to replace the top end along with the thickness of the base gasket?thank u

Admin reply: Hi Joe,

Look at top of piston. It i stock at 53.93mm. Oversizes come in 53.94, 53.95 etc.

Base gaskets come from .2 mm to .5mm in .1mm increments.

The site has a lot of TM info. Feel free to ask questions so that you can get started off right.

Added: August 17, 2010

Submitted by

Comments:

Name: juanlangarica
E-mail: Contact

hi tom i was checkingthe long track kit for tm k9 and it shows a vforce valve

is there a vforce that fits a k9 engine?

regards

juan

Admin reply: Yes, there is a V Force that fits TM ICC - V3110A. But we are finding that the TM KZ10 reed set works well.

Added: August 10, 2010

Submitted by

Comments:

Name: tom ginn
E-mail: Contact

just to clarify, no, the idle speed screw doesn't cause any change in speed. The minimum opening of the tv to idle properly is being done by adjusting the throttle cable end point. By the way, transition and top end are ok. But something must be wrong with idle circut, don't you think?

Admin reply: Yes, I believe there may be something wrong with idle/air screw. If the other crcuits are correct the idle/air should affect idle speed somewhat when turning in or out.

Added: July 20, 2010

1 2 3 4 5 | Next > | Last >>